TEST PRODUCTS INTERNATIONAL(TPI 460) 20Mhz Handheld Oscilloscope, FREE SHIP NEW!

Description

THIS SALE IS FOR A NEW TPI 460 20MHz DIGITAL O-SCOPE, IN ORIGINAL CASE, WITH ALL DOCUMENTS, AND ALL ACCESSORIES INCLUDED FROM THE FACTORY. THE ORIGINAL CARDBOARD BOX IS NOT INCLUDED. THIS UNIT IS BRAND NEW NEVER USED AND HAS NEVER BEEN REGISTERED WITH THE FACTORY FOR THE FACTORY WARRANTY. IT WAS PURCHASED FOR A DEFENSE CONTRACT THAT NEVER RECEIVED FULL FUNDING. THE COMPANY HAD WRITTEN THEIR NAME ON THE BACK OF THE SCOPE. I  CAN REMOVE IT AS THE GHOSTING OF THAT WRITING  CAN STILL BE SEEN, AND  I WANT TO BE PERFECTLY HONEST AS ALWAYS. THE UNIT STILL HAS THE REMOVABLE SCREEN PROTECTOR ON IT, IT WAS NEVER TAKEN OFF. UNIT HAS BEEN FULLY TESTED AND IS PERFECT!! UNIT PART NUMBER= TPI 460. THIS UNIT HAS A RETAIL OF 0.58 AND WORTH EVERY PENNY OF THAT!!!
WHY NOT SAVE A BOATLOAD OF CASH, YOU ARE GOING TO TOSS THE CARDBOARD EXTERIOR BOX ANYWAY AND THE GHOSTED IMAGE ON THE REAR HAS ZERO EFFECT ON FORM/FIT/FUNCTION.
This item qualifies for eBay Fast N Free - 1 day handling and free domestic shipping with Fedex
Ground/Home OR USPS GROUND, UPS GROUND OR OTHER TRACKABLE CARRIER to the lower 48 USA.
AK, HI, PR to pay actual shipping.
TPI 460 20Mhz Handheld Oscilloscope
Item specifics
Condition:
New:
A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
...
Read more
about the condition
Brand:
TEST PRODUCTS INTL.
Sampling Rate:
25MSa/s Single Channel, 500MSa/s Second Channel
ManufacturerPartNumber:
460
Manufacturers Warranty Length:
3 Years
SKU:
G4676296
Battery Life:
2.5 Hours With Backlight On
Item:
Handheld Oscilloscope
Bandwidth (MHz):
20
Display:
3"x3" Cold Cathode Florescent
Input Sensitivity:
50mV/div to 200V/div
Safety Rating:
CAT II 1000V, CAT III 600V
Product Features
20 MHz Bandwidth
Enough bandwidth to capture signals from AC/DC drive motors, sensors, actuators, line and control voltages, UPS and industrial machines.
Sample Rate
A real time sampling of 25 megasamples/sec to capture spikes and dropouts of industrial signals.
Dual Input
View two waveforms on the display for comparison and troubleshooting.
True RMS DMM
Includes a 4000 count True RMS DMM that measures AC/DC volts to 600, frequency to 20MHz, resistance to 20MegOhm, diode test and continuity buzzer.
Bright LCD Backlight
Easy-to-see in any light conditions with user-adjustable brightness levels.
Optically Isolated RS232 Output
Transfer data safely without any direct connections to your computer’s systems circuitry.
What's in the Box?
TPI 460 digital oscilloscope and multimeter
Set of insulated test leads with alligator clips
7.2V rechargeable NiCad battery pack
Charger/adapter
User manual
Optional Accessories:
Temperature Adapter to measure temperature from -40 to 500°F (A301)
Pressure Adapter to measure pressure from -30 to 500psi (A620)
Current Adapters • For measuring low current in milliamps (A254) • Up to 400AC/DC amps (A256) • And up to 1000 AC/DC amps (A296)
Protective Boot (A405)
Soft Carrying Case with shoulder strap (A905)
Software and RS232 cable (A404)
Applications
Industrial motor control View start-up in rush currents, waveform symmetry, SCR trigger pulses, variable frequency drive signals, pulse width modulation, noise, misc. AC and DC speed control signals.
Power quality Noise on industrial feeds, AC voltage waveshape, current waveforms, machine start-up/power quality interference and noise.
Programmable logic controls PLC input and output signals, control signals, signal conditioning circuits, communications lines and power supplies.
NC machines Power quality, sensor outputs, control circuits, safety circuits, calibration and adjustments.
Uninterruptable power supplies Sensing and monitoring circuits, switching circuits, output waveforms and current waveforms.
Audio Public address feeds, amplifiers, mixers and preamps.
Video Horizontal and vertical scan rates, z-axis blanking, sync pulses and luminance.
Industrial lighting controls SCR’s and other solid state designs.
Factory automation Robot control signals, machine vision, machine control and sensing circuits, calibration of positioning systems, analog controllers and servo controls.
Line conditioners Noise and quality.
Voltage regulators Noise and stability.
Inverters Waveform quality.
The 460 hand held oscilloscope features a 3” x 3” cold cathode fluorescent display providing test data in a clear easy to see format. The cursor readout function allows the width and amplitude of a signal to be measured precisely instead of trying to figure it out manually.
20 MHz Bandwidth
Cursor Readout
Decibels
Pre and Post Triggering
Trend Mode
Dual Input
True RMS DMM
Real Time Sample Rate
Bright LCD Backlight
Optically Isolated RS232 Output
Continuous Autoset
460 Specifications
DISPLAY
Size
3” x 3” (76mm x 76mm)
Pixels
240 x 240
Backlight
Yes
POWER
External
5V DC power supply (Included)
Internal
4.8V DC rechargeable battery
Operating Time
2.5 Hours with backlight on
Charging Time
10 Hours
MEMORY
Waveform
Save 2 full screens
Setup
Saves user settings
VERTICAL
Sample Rate (-3dB)
Real Time: 25 Megasamples per Second up to 2 MHz
Equivalent Time: 500 Megasamples per Second > 2 MHz
Bandwidth
20 MHz w/SP60B 10:1 Probe
10 MHz w/Shielded Test Leads
Resolution
8 bits
Channels
2
Coupling
AC, DC AC, DC, GND (max: 750V)
Input Impedance
Approximately 1M Ohm
Sensitivity
50mV TO 200V/div 1,2,5 Sequence
Accuracy
± 3% ± (3% + 0.05 range/div)
Trigger Position
Ver1;Fixed Position / Ver3; Adjustable Position
Trigger Mode
Free Run, Normal
Trigger Source
Internal
Trigger Slope
Positive / Negative
Trigger Sensitivity
Equivalent Time: 3 divisions or more
Real Time: 2 divisions or more
HORIZONTAL
Samples per Division
25
Time / Division
50nS to 500nS / DIV (equivalent times)
1uS to 2S / DIV (real time)
Modes
Single, Normal, Auto
Accuracy
Equivalent Time : ± (0.5% + 0.08 time/div)
Real Time: ± (0.1% + 0.04 time/div)
TREND MODE
Plot Time
30 sec/div to 1 hour/div
Plot Data Type
Max/Min Selectable
Memory
2 Screens
TRUE RMS DMM
DCV (CH1, CH2)
400mV, 4, 40, 400, 600V
Basic DC Accuracy
± (0.5% + 5 digits)
ACV (CH1, CH2)
400mV, 4, 40, 400, 600V
Basic ACV Accuracy
± 0.75% ± (1% + 10 digits)
Frequency (CH1, CH2)
1 Hz to 20 MHz
Basic Frequency Accuracy
± (0.5% + 5 digits)
Ohm (CH1 only)
400, 4k, 40k, 400k, 4M, 20M
Basic Ohm Accuracy
± (0.5% + 5 digits)
Continuity (CH1 only)
< 0.1k ohm, ± (2% + 5 digits)
Diode Test
5mA maximum output
460 Applications
Power Quality
Variable Speed Drives
Industrial Motor Controls
Battery Testing
Programmable Logic Controls
NC/CNC Machines
Uninterruptable Power Supplies
Audio
Video
Industrial Lighting Controls
Factory Automation
Line Conditioners
Voltage Regulators
Inverters
Gaming Industry
Oscilloscopes FAQs
Where do I use your oscilloscopes?
They are ideal for viewing industrial power signals, UPS systems, power supplies and PLC controls. Use anywhere a DMM is used.
Does the oscilloscopes measure capacitance?
Yes, the 440 can measure up to 400uF (microfarads).
What is the highest voltage the oscilloscopes can measure?
They can measure up to 1,000 DCV and 1,000 ACV.
What is the lowest voltage the 440 can measure?
The 440 can measure down to 0.1 millivolts on both DCV and ACV. The scope also has a volts/division setting of 0.1 volts.
How is the RS232 port used?
With the optional A402 cable and software you can acquire data and download it to a spreadsheet.
Can your oscilloscopes measure more than 10 DCA or ACA?
Yes, TPI offers a number of amp adapters to extend the range up to 1,000 amps. TPI has a wide range of optional accessories that enables the user to measure amps, temperature, pressure, or CO.
Why do you need a 20 MHz oscilloscope (460)?
To measure signals and voltage anomalies, and to look for glitches that may damage or even shutdown electronic machinery. View sine waves on power supplies, motors, and bead board circuitry. Pinpoint certain glitches on the sine wave to zero inon the problem and monitor changing patterns or distortion in electrical currents.
What are the different waveform patterns displayed on your handheld oscilloscopes?
An AC waveform known as sine wave displays voltage against time in the shape of a sine curve. The saw toothwave form displays a ramped angleand a sharp downward return to its earlier value. (Its display pattern resembles the cutting edge ofa saw.) A square waveform graphically plots a series of vertical square shapes repeated with spacing between peaks.
Why is it important to have Trend Mode?
Trend Mode is great for monitoring sudden intermittents caused by loose connections, dirt, or damaged wires. By setting the minimum and maximum parameters, you can monitor, even record the changes.
What is the purpose of triggering?
Simply zoom in on certain parts of the sine wave and “hold” to measure and monitor that particular part you are reading. A must have when searching for glitches and distortion on all measurements.